[ Chinese wardrobe net ] If the dream-free cloakroom is neglected, it will become a grocery room with nowhere to go. In the real space, if you can choose the right place in the wardrobe , cabinet, cabinet door and accessories, and master some effective finishing techniques and adhere to the application, the stand-alone wardrobe can also be refined and easy to use. Let's take a look at how to install it with Xiaobian. Don't decorate it wrong. 1. Use a mat to place the floor. Start by assembling the wide side panel against the end of the wall. Place the wide side panel on the ground (maintain 700mm away from the rear wall). First, put the plate of the filled three-in-one rubber plug on the cloth, check the hole spacing and the drawing, and install the three-in-one single-link. Then the solid layer is nailed to the cork, fixed on the wide side plate, the top handle with the large handle hole facing upward, the other solid layers are facing downward, and the foot line large handle hole is facing inward (the middle solid layer is consistent with the L frame height, that is, the bottom plate to the solid layer The inner space is 960mm, and the hole is drilled on site.) Put the side panels, nail the cork, and the cork is required to connect the solid layers on both sides. Install the double connecting rod on the second cabinet. Note that the large handle on the double connecting rod can only lock half, that is, 90°. When the two solid layers are fixed to the side plates, tighten the large handles at the same time. Repeat the installation steps for the second cabinet when installing the third cabinet. 2, nail back board. Place the assembled whole cabinet on the floor of the point cloth, and lay the side panels in the same plane. Use a slider to measure the diagonal size of the cabinet and adjust it to the same level. Start with the first backing plate from the wide measuring board. Note that if there is a solid nail in the middle, draw the center line of the solid layer with a pencil and nail it. nail. 3. Installation of the L frame. Use the side plates of the L frame to have a parallel line on the corresponding side plates, then move the center line of the three-in-one rubber particles up by 9 mm, and draw a parallel line on the corresponding bottom plate with the top frame of the L frame. The inner center 9mm draws the center line of three rubber pieces. The hole was drilled with a 10 mm drill bit and the hole depth was 10-20 mm. Install a single pole. After the L frame is installed, nails are fixed on the back plate. 4, clean the wardrobe installation debris, left and right station one person, the wardrobe is slightly inclined backwards, forcefully lifted, moved back to the desired position, pay attention not to scratch the floor, the wall. 5. Installation of push-pull mirrors. The three-section rail is mounted on the push-pull mirror, and the height of the push-pull mirror is generally 1700 mm above the bottom solid layer (customer can request height). The rail transverse line is drawn on the side panel at a height of 90° according to the required height. The parallel distance between the new eyes in the three-section track on the upper line is measured, and accurate data is obtained. The lower track transverse line is drawn on the side plate with a 90° angle. Install the upper and lower mother rails of the push-pull. The mother rail is 5mm away from the backboard and is equipped with a push-pull mirror. 6, the installation of Yitong. Move the 38mm draw cross-cut line from the ground level, the side plate is divided into the vertical cut line, and the cross pad is the center position of the first eye above the clothes pass. Some of the steel pipes of the cloth closet have the number marked, you can put them together with the number. The specific cloth wardrobe installation method is: 1. Find the parts of the chassis and put them together. Note that it is only the bottom part. Some have a shoe rack, you have to install the shoe rack first. 2, note that the second step is not to put the rest of the shelves, and the first on the cloth. Open the zipper of the cloth, and the place where the middle sticks is also pulled open, bottom down. There are some small holes dug in the bottom of the cloth. Pull the cloth from top to bottom according to each hole and pull down the vertical tubes. You can not pull to the bottom first. 3. Put the rest of the pipe in the cloth, then pull the cloth up, cover the top of the pipe, and adjust it until the cloth looks flat and there are no wrinkles. 4. Our installation is complete. Note: Some are plastic interfaces, sometimes they are a bit tight. Don't use strong force to insert, accidentally crack, no place to buy accessories. Do not screw one on the screw interface, it will bring difficulties to the future installation. First loosely put the shelves up, and after loading them, use the screwdriver to tighten all the screws. This way you will get a sturdy cloth wardrobe! Rechargeable Sonic Electric Toothbrush Rechargeable Sonic Electric Toothbrush,Adult Electric Toothbrush,Portable Household Electric Toothbrush,Special Sonic Electric Toothbrush ZHEJIANG SHENGFA ELECTRIC APPLIAMNCES CO.,LTD , https://www.shengfa-appliance.com
How to install the wardrobe decoration